收藏本站
A Product Line of
Diodes Incorporated
ZXLD1371
Applications Information (cont.)
In the event of more than one fault/warning condition occurring, the higher severity condition will take precedence. E.g.
‘Excessive coil current’ and ‘Out of regulation’ occurring together will produce an output of 0.9V on the STATUS pin.
If V ADJ >1.7V, V SENSE may be greater than the excess coil current threshold in normal operation and an error will be
reported. Hence, STATUS and FLAG are only guaranteed for V ADJ <=V REF .
Diagnostic signals should be ignored during the device
start – up for 100 μ s. The device start up sequence will
be initiated both during the first power on of the device
or after the PWM signal is kept low for more than
15ms, initiating the standby state of the device.
In particular, during the first 100 μ s the diagnostic is
signaling an over-current then an out-of-regulation
status. These two events are due to the charging of
VREF
0V
O ut of
re g u la tio n
the inductor and are not true fault conditions.
O ver
C u rre n t
2 2 5 m V /R 1
0A
100us
Figure 16. Diagnostic during Start-up
Reduced Input Voltage Operation
To facilitate operation in automotive and other applications, that have large transient reductions in system supply voltage,
the ZXLD1371 is now capable of operating down to input voltages as low as 5.0V. Care must be taken when operating at
these lower supply voltages to ensure that the external MOSFET is correctly enhanced and that the boosting ratio is not
increased to excessive amounts where both the duty cycle and peak-switch current limits are not exceeded. The device
will operate down to 5.0V, but for reliable start up V IN must be higher than 5.4V. The designer should also take into
account any noise that may occur on the supply lines.
In Buck-boost and Boost modes (most common topologies for applications likely to require transient operation down to
supply voltages approaching 5.0V) as the input voltage reduces then the peak switch current will increase the ZXLD1371
compensates for this by allowing the sense voltage to increase while maintaining regulation of the LED current. However if
the boost ratio (switch output voltage/input voltage) is increased too much then the sense voltage could be increased too
much causing an over-current flag to be triggered and/or loss of regulation.
In addition to this, increased power dissipation will occur in the external MOSFET switch – especially if the external
MOSFET has a large threshold. One way of overcoming this is to apply a boot-strap network to the V AUX pin – see next
section.
If the ZXLD1371 is used in buck mode at low voltages then the boot-strap network cannot be implemented and so a low
threshold MOSFET with low gate capacitance should be used. Some loss of regulation is expected to occur at voltages
below 6V – see Buck mode Typical Characteristics Section.
When using the ZXLD1371 in applications with transient input voltage excursions we recommend using the web calculator
to optimize operation over the normal operating band. Then change the input range to include the transient excursion while
keeping the optimized component selection to check expected function during the transient input voltage conditions.
ZXLD1371
Document number: DS35436 Rev. 1 - 2
37 of 42
www.diodes.com
February 2012
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ZXLD1374EST20TC IC LED DVR BUCK BOOST 20TSSOP
ZXLD1937ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD381FHTA IC LED DRIVR WHITE BCKLT SOT23-3
ZXLD383ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXSC300E5TA IC LED DRVR WHITE BCKLGT SOT23-5
ZXSC380FHTA IC LED DRVR WHITE BCKLGT SOT23-3
ZXSC400E6TA IC LED DRVR WHITE BCKLGT SOT23-6
0-1005447-1 SENSOR PIEZO FILM VIBRA MASS
相关代理商/技术参数
ZXLD1374 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:60V HIGH ACCURACY 1.5A BUCK/BOOST/BUCK-BOOST
ZXLD1374_11 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:60V HIGH ACCURACY 1.5A BUCK/BOOST/BUCK-BOOST
ZXLD1374EST20TC 功能描述:LED照明驱动器 60V 1.5A BUCK/BOOST LED DRIVER AEC-Q100 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1601 制造商:ZETEX 制造商全称:ZETEX 功能描述:ADJUSTABLE DC - DC BOOST CONVERTER WITH INTERNAL SWITCH IN SC70
ZXLD1601H6 制造商:Diodes Incorporated 功能描述:LCD/OLED BIAS BOOST CONVERTER SMD
ZXLD1601H6TA 功能描述:开关变换器、稳压器与控制器 Boost Converter for LCD and OLED BIAS RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
ZXLD1601H6TC 功能描述:开关变换器、稳压器与控制器 Boost Converter for LCD and OLED BIAS RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
ZXLD1615 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:ADJUSTABLE DC-DC BOOST CONVERTER WITH INTERNAL SWITCH IN